Eric

What Causes Electric Power Steering Problems? 9 Common Reasons Explained

Table of Contents

Quick Answer

Electric power steering (EPS) problems can result from low battery voltage, damaged fuses or wiring, faulty torque or position sensors, motor or control-module faults, software or communication errors, and mechanical resistance in the steering rack or linkage. Because these faults can cause similar symptoms, diagnosis should check the power supply, EPS fault codes, sensor data, motor operation, and mechanical components before parts are replaced.

What Is Electric Power Steering and How Does It Work?

Electric Power Steering (EPS) is a steering assistance system that uses an electric motor to reduce the effort required to turn the steering wheel. Unlike traditional hydraulic power steering, EPS does not rely on an engine-driven hydraulic pump or steering fluid.

When the driver turns the steering wheel, a torque sensor detects the applied steering force and sends signals to the Electronic Control Unit (ECU). The ECU processes this information, together with vehicle speed and other relevant data, to calculate the required steering assistance.

It then controls an electric motor to generate additional torque, which is transferred through a steering column, pinion, or rack mechanism, depending on the system design.

The main EPS components include:

  • Torque Sensor: Detects the direction and amount of force applied to the steering wheel.
  • Electric Motor: Generates the additional torque needed to assist steering.
  • EPS Control Module (ECU): Processes sensor signals and controls motor operation.
  • Motor Position Sensor: Monitors motor position and rotation where required.
  • Steering Angle Sensor: Provides steering position information in systems that use this signal.
  • Electrical Wiring and Connectors: Supply power and transmit control signals.
  • Steering Rack and Pinion: Transfer steering input to the wheels.

Because these components work together, a fault in one part can affect the performance of the entire steering assistance system.

What Is the Difference Between EPS, EHPS, and Hydraulic Power Steering?

Identifying the correct steering system is essential when diagnosing power steering problems because different systems have different components and failure mechanisms.

Steering System Working Principle Main Components Common Problems
Hydraulic Power Steering (HPS) Engine-driven hydraulic pump provides steering assistance Hydraulic pump, fluid reservoir, hoses, steering rack Fluid leaks, pump wear, low fluid
Electro-Hydraulic Power Steering (EHPS) Electric motor drives a hydraulic pump Electric pump, hydraulic fluid, hoses, reservoir Pump failure, fluid leaks, electrical faults
Electric Power Steering (EPS) Electric motor directly provides steering assistance EPS motor, ECU, torque sensor, wiring, steering mechanism Low voltage, sensor faults, motor failure, software errors

Pure EPS systems do not use hydraulic steering fluid to generate assistance. However, EHPS systems still rely on hydraulic pressure, even though their pumps are electrically driven.

This distinction matters because hydraulic pump or fluid leakage problems should not be classified as direct faults of a conventional EPS system.

What Causes Electric Power Steering Problems? 9 Common Reasons

Electric power steering problems can originate from several electrical, electronic, software, and mechanical components. The following are nine common causes.

1. Weak Battery or Charging System Problems

A weak battery or defective charging system can cause insufficient or unstable electrical power, affecting EPS operation.

The electric steering motor can require substantial current, particularly during low-speed steering and parking. If the battery cannot provide sufficient power or the alternator fails to maintain the required voltage, the EPS system may reduce assistance or temporarily shut down.

Common causes include:

  • Weak or aging batteries.
  • Defective alternators.
  • Loose or corroded battery terminals.
  • Damaged battery cables.
  • Poor grounding connections.

Possible symptoms include heavy steering, an illuminated EPS warning light, or intermittent power assistance.

Battery condition, charging performance, and voltage drop should be tested according to the vehicle manufacturer’s specifications. There is no single voltage threshold that applies to every EPS system.

2. Blown Fuses, Damaged Wiring, or Poor Electrical Connections

EPS systems depend on dedicated electrical circuits to supply power to the motor and control module.

A blown fuse, loose connector, damaged wire, or poor ground connection can interrupt the power supply or prevent important signals from reaching the ECU.

Common electrical problems include:

  • Blown EPS fuses.
  • Loose motor or ECU connectors.
  • Corroded electrical terminals.
  • Damaged wiring harnesses.
  • Short circuits.
  • Poor grounding connections.

These faults may cause complete or intermittent loss of steering assistance.

If an EPS fuse repeatedly blows, the underlying cause should be identified rather than simply replacing the fuse. A short circuit, damaged motor, or excessive current draw may be responsible.

3. Faulty Torque Sensors or Steering Position Sensors

EPS relies on accurate sensor information to calculate the required steering assistance.

The torque sensor measures the force applied by the driver and helps the ECU determine the direction and amount of assistance required.

A faulty torque sensor may cause:

  • Uneven steering assistance.
  • Delayed steering response.
  • Inconsistent steering effort.
  • Jerky steering assistance.
  • EPS warning lights.

Steering angle and motor position signals may also affect system operation, depending on the vehicle’s design.

It is important to distinguish these sensors: a torque sensor measures driver-applied steering force, a steering angle sensor measures steering position, and a motor position sensor monitors the electric motor.

Technicians should check diagnostic codes, wiring, live sensor data, and calibration before replacing any sensor. Some sensors are integrated into the steering column or rack assembly.

4. Electric Power Steering Motor Failure

The EPS motor generates the additional torque required to assist steering. If it develops an electrical or mechanical fault, steering assistance may become weak, inconsistent, or completely unavailable.

Common motor problems include:

  • Damaged motor windings.
  • Internal short circuits.
  • Worn bearings.
  • Excessive heat generation.
  • Motor position feedback faults.
  • Abnormal current consumption.

Motor overheating can also trigger protective functions in some EPS systems. During prolonged low-speed steering or operation under excessive mechanical resistance, the motor may experience increased electrical and thermal loads.

The system may temporarily reduce or disable assistance until operating conditions return to an acceptable range.

If assistance returns after cooling down, the underlying problem may still exist. Motor condition, electrical supply, and mechanical steering resistance should be checked.

5. EPS Control Module (ECU) Failure

The EPS Electronic Control Unit is responsible for processing sensor signals and controlling the electric motor.

If the ECU develops an internal electronic fault, it may fail to calculate or deliver the correct steering assistance.

Potential causes include:

  • Damaged electronic circuits.
  • Internal component degradation.
  • Water intrusion.
  • Excessive heat.
  • Unstable power supply.
  • Internal motor-driver faults.

A defective ECU may cause warning lights, intermittent assistance, or complete loss of electric steering support.

However, an illuminated EPS warning light does not automatically mean the ECU is defective. Sensor faults, power supply interruptions, wiring problems, and communication errors can produce similar symptoms.

Some vehicles integrate the ECU and motor into the steering rack or column assembly, which affects the available repair and replacement options.

6. Software Errors and CAN Bus Communication Problems

Modern EPS systems depend on software, calibration data, and communication with other vehicle control modules.

The EPS ECU may receive information from the ABS, Electronic Stability Control (ESC), and vehicle speed sensors through the Controller Area Network (CAN bus).

Software errors, incorrect programming, or communication interruptions can cause abnormal steering assistance or activate system protection functions.

Common causes include:

  • Incorrect EPS software configuration.
  • Software calculation errors.
  • Incomplete ECU programming.
  • Incorrect sensor calibration.
  • CAN bus wiring faults.
  • Communication interruptions between control modules.

For example, replacing an EPS steering rack or ECU without completing the required coding and initialization may cause warning lights or abnormal system operation.

Real-World Example: Honda and Acura EPS Software Recall

NHTSA Recall 26V721, filed in October 2026, covers 635,808 potentially affected vehicles, including certain 2021–2025 Acura TLX, 2022–2024 Acura MDX, and 2023–2025 Honda Pilot models.

The recall involves an incorrect EPS software configuration that may cause an internal calculation error under certain operating conditions. The system may enter failsafe mode and disable steering assistance.

The specified remedy is free EPS control unit reprogramming by authorized dealers.

This case demonstrates that EPS failure does not always originate from a physically damaged motor, sensor, or steering rack. Software errors can also cause loss of steering assistance. Vehicle owners should verify recall eligibility using their VIN.

7. Mechanical Problems in the Steering Rack and Linkage

Although EPS uses electronic control, it still depends on mechanical components to transfer steering movement to the wheels.

Wear, damage, or excessive friction in these components can increase steering resistance, even when the electronic assistance system is functioning correctly.

Common mechanical problems include:

  • Worn rack and pinion gears.
  • Damaged steering rack bearings.
  • Bent rack shafts.
  • Worn steering column joints.
  • Binding tie rod ends.
  • Damaged ball joints or suspension components.

These problems may cause heavy steering, knocking noises, grinding, or poor steering wheel return.

Excessive mechanical resistance can also increase the load on the EPS motor, potentially triggering thermal protection or abnormal current consumption.

Therefore, technicians should inspect the complete steering and suspension system before concluding that the EPS motor or ECU needs replacement.

8. Water Intrusion, Corrosion, and Environmental Damage

EPS components are exposed to road vibration, moisture, dust, temperature changes, and other environmental conditions.

If water enters electrical connectors, wiring harnesses, or electronic assemblies, it can cause corrosion, unstable signals, short circuits, or component damage.

Potential causes include:

  • Floodwater exposure.
  • Damaged connector seals.
  • Moisture inside wiring connections.
  • Corrosion caused by road salt.
  • Excessive heat exposure.
  • Damaged protective covers.

The steering rack’s protective bellows also help prevent water and dirt from entering internal mechanical areas. Damaged rack boots may allow contamination to accelerate corrosion and wear.

However, exposure to rain or normal wet-road conditions does not automatically mean an EPS component will fail. Actual damage depends on component protection, sealing condition, and exposure severity.

9. Collision Damage or Incorrect Installation

EPS problems can also develop after accidents, steering system repairs, or replacement of major components.

A collision or severe road impact may damage the steering rack, column, mounting points, electrical connections, or sensors.

Incorrect installation can create additional problems, including:

  • Damaged electrical connectors.
  • Improperly routed wiring.
  • Incorrect steering wheel centering.
  • Incomplete calibration or initialization.
  • Incompatible replacement steering racks or ECUs.
  • Incorrect software configurations.

Two steering racks may look similar but have different OE references, motor specifications, connector arrangements, or electronic configurations.

For distributors and importers, verifying OE numbers and vehicle applications is essential when sourcing replacement steering components.

What Are the Common Symptoms of Electric Power Steering Problems?

Different EPS faults can produce similar symptoms. The following table connects common warning signs with possible causes and components to inspect.

Common Symptoms Possible Causes Components to Check
Steering suddenly becomes heavy Low voltage, fuse failure, motor or ECU fault Battery, alternator, EPS motor, ECU
EPS warning light stays on Sensor, communication, or software fault Torque sensor, ECU, wiring
Steering assistance works intermittently Loose connectors, unstable voltage, overheating Wiring, battery, motor
Steering feels uneven left to right Sensor signal error, calibration issue, mechanical resistance Torque sensor, steering rack
Grinding or knocking noises Gear wear, bearing damage, loose components Steering rack, pinion, tie rods
Steering wheel does not return smoothly Mechanical binding or alignment problems Steering rack, ball joints, suspension

These symptoms are diagnostic clues, not proof of a particular component failure. A proper inspection is necessary before replacing parts.

How Are Electric Power Steering Problems Diagnosed?

Accurate EPS diagnosis requires checking both electronic and mechanical components.

A practical diagnostic process includes:

  1. Identify the EPS system type: Determine whether the vehicle uses column-assist, pinion-assist, or rack-assist EPS.
  2. Check the electrical supply: Test battery condition, charging performance, fuses, grounding, and voltage drop.
  3. Read EPS fault codes: Use a diagnostic scanner capable of accessing the EPS control module, not just the engine ECU.
  4. Check sensor signals: Examine torque sensor, steering position, and motor position data where applicable.
  5. Test the motor and ECU: Verify power supply, control signals, and operating condition.
  6. Inspect mechanical components: Check the steering rack, tie rods, joints, and suspension for wear or binding.
  7. Verify the repair: Complete any required programming, initialization, and calibration according to manufacturer procedures.

Diagnostic trouble codes help identify abnormal conditions, but they do not automatically confirm that the named component must be replaced.

Should You Repair or Replace an Electric Power Steering Component?

The right solution depends on the actual failure and the vehicle’s design.

Minor electrical problems, such as loose connectors, damaged wiring, or corroded terminals, may be repaired without replacing the complete steering assembly.

Faulty sensors, motors, and control modules may be individually serviceable on some vehicles. However, other designs integrate these components into the steering column or rack assembly.

Complete steering rack replacement may be necessary when internal gears, bearings, shafts, housing, or integrated electronic components are severely damaged.

Before purchasing a replacement EPS assembly, verify:

  • Vehicle make, model, and production year.
  • Original Equipment (OE) reference number.
  • Steering system configuration.
  • Motor and ECU specifications.
  • Electrical connector and mounting details.
  • Software and calibration compatibility.

Replacing the entire EPS assembly without identifying the root cause can increase repair costs without resolving the original problem.

Can You Drive a Car With Electric Power Steering Problems?

The safety of driving with EPS problems depends on the type and severity of the fault.

Many EPS-equipped vehicles retain a mechanical connection between the steering wheel and the road wheels when electric assistance is lost. However, steering effort may increase significantly, especially at low speeds.

If the steering suddenly becomes heavy, responds unpredictably, or produces abnormal mechanical noises, drivers should slow down carefully and stop in a safe location.

Professional inspection or towing may be necessary. Restarting the vehicle should not be considered a permanent solution, even if steering assistance temporarily returns.

How Can Electric Power Steering Problems Be Prevented?

Although pure EPS systems do not require conventional hydraulic steering fluid, regular vehicle maintenance can help reduce the risk of electrical and mechanical failures.

  • Maintain the battery: Check battery condition and charging performance according to manufacturer recommendations.
  • Inspect electrical connections: Look for corrosion, moisture, damaged insulation, and loose terminals.
  • Protect steering components: Check rack boots, seals, and accessible connectors for damage.
  • Maintain the steering and suspension system: Inspect tie rods, ball joints, steering joints, and rack components.
  • Address warning lights promptly: Diagnose EPS warnings and intermittent assistance instead of ignoring them.
  • Use compatible replacement parts: Verify OE references, vehicle applications, and calibration requirements before installation.

Frequently Asked Questions About Electric Power Steering Problems

What is the most common cause of electric power steering problems?

Low battery voltage and electrical supply problems are common causes. Faulty sensors, wiring, motors, ECUs, and mechanical steering components can also affect EPS operation.

Can a bad battery cause electric power steering to stop working?

Yes. A weak battery may prevent the EPS motor and control module from receiving sufficient electrical power, resulting in reduced or lost steering assistance.

Does electric power steering use hydraulic fluid?

No. Pure EPS systems use an electric motor to provide steering assistance and do not require hydraulic steering fluid. EHPS systems are different because they still use hydraulic pressure.

Can a faulty torque sensor cause heavy steering?

Yes. Incorrect torque sensor signals can prevent the EPS ECU from calculating the required assistance, resulting in heavy or inconsistent steering.

Can an electric power steering rack be repaired?

In some cases, yes. Repair depends on the damaged components, vehicle design, and availability of serviceable parts. Severe mechanical or integrated electronic damage may require complete assembly replacement.

Why does electric power steering fail intermittently?

Common causes include loose connectors, unstable voltage, overheating, faulty sensor signals, and control module problems. Stored fault codes and live data can help identify the cause.

Can software problems cause EPS failure?

Yes. Incorrect software configuration, programming errors, or communication faults can cause the EPS system to enter failsafe mode and disable steering assistance.

Does replacing an EPS steering rack require calibration?

Some vehicles require steering angle calibration, sensor initialization, ECU coding, or software programming after replacement. Requirements vary by vehicle manufacturer.

Summary

Electric power steering problems can originate from electrical supply issues, damaged wiring, faulty sensors, motor failure, ECU defects, software errors, or mechanical steering damage.

Because these faults can produce similar symptoms, an EPS warning light or heavy steering wheel does not automatically mean the complete steering rack needs replacement.

Accurate diagnosis, correct OE matching, and proper installation are essential for restoring reliable steering assistance and selecting compatible replacement components.